Nortrac NorTrac 35XT Owner'S Manual Download

Page: 70 / 98

Maintenance Instructions

4.9.2 Air Filter Maintenance

•

Take out the air filter element. Use a brush to clean the inner case of the air filter and remove the dust

from the rubber dust bag.

•

Turn the filter element, and use compressed air of less than 500KPa (72.5 psi) to blow the dust from

the inside of the filter element.

•

Re-install the air filter element.

4.10 Fan Belt Tensioning Adjustment

Press down on the middle part of the fan belt with your thumb.

The exerted force should be 29.4–49.0N (6.6 – 11lb), and the

deflection should be 15±3mm (0.6–0.7 in). If this requirement

is not met, the belt tension should be adjusted accordingly. The

adjustment method is as follows:

Loosen the lock nut on the alternator support arm. Pivot the

alternator outwards to tension the belt, and then tighten the lock

nut on the alternator support arm.

Figure 4-11 Fan Belt Tensioning Adjustment

IMPORTANT ITEMS

Correct use and maintenance of the air filter directly relates to the service life of the

engine. Therefore, the air filter should always be kept clean. When the tractor is used on a farm, the air filter should

be checked and cleaned after each working period.

Summary of Contents for NorTrac 35XT



































































































Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands

Nortrac NorTrac 35XT, Owner'S Manual

Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands