Nortrac NorTrac 35XT Owner'S Manual Download

Page: 66 / 98

Maintenance Instructions

4.5 Steering System Adjustment

4.5.1 Full Hydraulic Steering System Precautions

The 35XT Series 4-wheeled tractors use a full hydraulic steering mode, as shown in the following figure. Before

each tractor leaves the factory the steering system is adjusted. Pay attention to the following when using the

tractor:

•

Check the threaded connections frequently and tighten them if there is any looseness. There should be no

leakage in any connection when the full hydraulic steering system is working.

•

During use, if steering becomes difficult or fails, troubleshoot the problem. Do not turn the steering wheel too

hard or disassemble the steering gear, so as to avoid damage to the parts. Never have two people turning the

steering wheel together.

•

When installing the full hydraulic steering system, the steering gear should coaxial to the steering shaft, and

there should be some clearance between them in the axial direction. After installation, check whether the

steering wheel turns easily.

•

Ensure that the oil is clean. Check the oil and filter element often. The method is as follows: Put a drop of oil

on to a paper towel, and change the oil if there is a black spot in the center of the oil mark.

•

The diverter valve is a precision component and should not be removed except in a clean environment. Clean

it with clean solvent.

•

Before leaving the factory, the pressure of the diverter valve has been adjusted correctly. Therefore, do not

remove or adjust this valve on your own. Replace if faulty.

Figure 4-6 Full Hydraulic Steering System

1. Steering Wheel 2. Jacket 3. Steering Column 4. Steering Gear 5. Diverter Valve Assembly 6. Steering
Gear Right Oil Pipe 7. Steering Gear Left Oil Pipe

Summary of Contents for NorTrac 35XT



































































































Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands

Nortrac NorTrac 35XT, Owner'S Manual

Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands