Nortrac NorTrac 35XT Owner'S Manual Download

Page: 88 / 98

Appendices

10.2

Main Bolts, Screws and Nuts Tightening Torque

Table 10-2 Main Bolts, Screws, and Nuts Tightening Torque Table

Name and Assembly Position

Thread

Specification

Tightening

Torque [N·m]

Tightening

Torque [LB FT]

The bolt and nut connecting the engine and the

clutch housing.

M10 41~51

30~37

The bolt connecting the clutch housing and the

rear axle casing.

M14X1.5 123~154 90~113

The bolt securing the bearing block of the primary

shaft and the secondary shaft.

M10 41~51

30~37

The bolt securing the interlocking wedge.

M10

50~70

36~51

The bolt connecting the slave drive spiral bevel

gear.

M10X1.25 45~55 33~40

The bolts connecting the drive shaft shell and the

rear axle housing.

M12

1.5 73~89 53~65

The bolt connecting the driving wheel hub and the

radial plate.

M18

1.5 397~457 293~337

The lock nut that locks the front shaft cross bar.

M16X1.5 122~149 90~110

The bolt connecting the subassembly of the front

outer shaft and the front inner shaft.

M14 122~149

90~110

The bolt connecting the front driving wheel, the

front wheel hub and the radial plate.

M14

1.5 178~218 131~160

The bolt connecting the front axle and the bracket.

M16

182~222 134~164

The bolt connecting the front bracket and the

battery tray.

M12 73~89

53~65

The bolt connecting the bracket and the engine.

M12 73~89 53~65

The bolt connecting the bracket and the engine.

M14X1.5 126~154 93~114

The bolt connecting the lifter shell and the rear

axle housing.

M10 41~51

30~37

The bolt connecting the steering gear and the

clutch housing.

M14 122~149

90~110

The coupling bolt for the limited rod support.

M14

122~149

90~110

Summary of Contents for NorTrac 35XT



































































































Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands

Nortrac NorTrac 35XT, Owner'S Manual

Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands