Nortrac NorTrac 35XT Owner'S Manual Download Page 23

Page: 23 / 98

Operation Description

Water Temperature Gauge

The Water Temperature Gauge displays the engine cooling fluid

temperature, increasing from left to right with the red area indicating

high temperature

Engine Tachometer and Hour Meter

The Engine Tachometer shows the operating rotary speed

of the engine in rpm once the tractor is started. Tractor running

hours are displayed in the lower hour meter box.

Oil Pressure Gauge

The oil pressure gauge displays the oil pressure level in the engine.

Amp Meter

The Amp meter is used to indicate the status of the battery. The indicator will

be in the + when the battery is properly charged.

Figure 2-4 Water Temperature Gauge

Figure 2-5 Engine Tachometer and Hour Meter

Figure 2-7 Amp Meter

Figure 2-6 Engine Oil Pressure Gauge

Summary of Contents for NorTrac 35XT



































































































Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands

Nortrac NorTrac 35XT, Owner'S Manual

Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands