Nortrac NorTrac 35XT Owner'S Manual Download

Page: 75 / 98

Maintenance Instructions

4.20 Engine Cooling System Maintenance

The engine cooling system uses a 50/50 water/antifreeze blend.

In general the antifreeze is good for a period of 2 years or 1,600

hours. After that the coolant should be replaced. The cooling

system should be flushed out before new coolant is added. Use

clean water for the flushing process.

Close the radiator drain valve, add a 50/50 water/antifreeze

mixture and run the engine for 20 minutes. Then shut off the

engine, let it cool down, and check for leaks and for the correct

coolant level

Figure 4-20 Cooling System
Maintenance

4.21 Bleeding the Fuel System

•

If the tractor is not used for a long time, or when the

diesel filter element is replaced, or the fuel tank is kept

empty, air could enter the fuel line, making it difficult

to start the engine. This problem can be fixed by

following the steps below but first the fuel tank should

be filled and the fuel cutoff switch turned on.

•

Unscrew the bleeder screw (A) on the fuel filter, and

then move the fuel supply pump draw knob (C) up and

down until there are no air bubbles in the diesel fuel

flowing out from the bleeder screw.

•

Tighten the fuel filter bleeder screw (A), and unscrew

the air bleed screw (B) on the fuel injection pump.

Pump the fuel supply hand primer knob (B) until the

there are no air bubbles in the diesel fuel flowing out

of the bleeder screw. Then tighten the fuel filter

bleeder screw (C).

Figure 4-24 Exhaust of Fuel System

IMPORTANT ISSUES

The engine runs on high quality light diesel oil and must meet specifications.

Generally, 2 light diesel oil should be used in summer, and 1 light diesel oil should be used in winter.

IMPORTANT ISSUES:

During winter, water in the radiator can freeze, causing the engine block to crack.

Always use antifreeze in the radiator.

Summary of Contents for NorTrac 35XT



































































































Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands

Nortrac NorTrac 35XT, Owner'S Manual

Search results

Summary of Contents for NorTrac 35XT

Reviews:

Related manuals for NorTrac 35XT

Brands by name

Popular brands