manualshive.com logo in svg

Nortel Call Recording, User Manual, Page: 70 / 94

Share
Download
Nortel Call Recording User Manual Download Page 70

Upgrade Procedures

Standard 1.0

70

Nortel Call Recording Card

XA upgrade using PCMCIA card to transfer firmware to compact 
flash card

Use this procedure to perform an XA upgrade using the PCMCIA card to 
transfer firmware to the compact flash card.

1

Reboot the card.

2

While the card reboots, when prompted, type 

jkl

 to access the bootROM.

3

Insert the PCMCIA Card into the faceplate PCMCIA Card slot.

4

Copy the loadware from the PCMCIA card (/A:/ drive) to the compact 
flash card (/C:/ drive) as shown in the following example:

copy("/A:/filename","/C:/filename")

5

Remove the PCMCIA Card from the faceplate slot.

Attention: 

Do not insert a card in the /A:/ drive when Nortel Call 

Recording Card is in normal operation.

6

Upgrade the XA firmware by typing the following command from the 
shell:

upgradeXa "<server IP address>", "<userid>", 

"<password>", "<path>", "<filename>" <CR>

Where <Server IP Address> is the IP address of the Nortel Call 
Recording Card. <userid> and <password> are the same as the shell 
user name/ password on the Nortel Call Recording Card. <path> is the 
location on the card where the XA firmware is located.

7

After the upgrade is complete, reboot the card.

Summary of Contents for Call Recording































































































Reviews:

No comments