manualshive.com logo in svg

Nortel Call Recording, User Manual, Page: 14 / 94

Share
Download
Nortel Call Recording User Manual Download Page 14

Installing the Nortel Call Recording Card

Standard 1.0

14

Nortel Call Recording Card

Installation overview

The following table documents the Nortel Call Recording Card installation 
information. 

Table 1: 

Nortel Call Recording Card applicability and compatibility

Nortel Call Recording 
Card

Application and Compatibility

Switch options

Small systems: 

„

Option 11 Cabinet / Chassis

„

Succession 1000

„

Succession 1000M Cabinet / Chassis

Large systems: 

„

Option 51C/61C/81/81C

„

Succession 1000M Half Group/Single Group/Multi 
Group

Card slot location

Option 51C,61C, 81 or 81C: any IPE slot except CONT

Any IPE slot in an Option 11 Cabinet / Chassis.

Succession 1000M Half Group / Single Group / Multi 
Group: any IPE slot except CONT.

Any IPE slot in a Succession 1000 or Succession 1000M 
Cabinet / Chassis.

Note: 

On older Option 51C to 81C systems (before IPE 

shelf vintage NT8D37EC) for slots other than 0, 4, 8, 
12, you must install the NT8D81AA backplane to I/O 
panel cable to connect all required signals to I/O panel.

MDF cabling

None (the sets are virtual).

Summary of Contents for Call Recording































































































Reviews:

No comments