manualshive.com logo in svg

Nortel Call Recording, User Manual, Page: 32 / 94

Share
Download
Nortel Call Recording User Manual Download Page 32

Configuring the Nortel Call Recording Card

Standard 1.0

32

Nortel Call Recording Card

Cabling the Nortel Call Recording Card 

Use this section to connect the Nortel Call Recording Card cables.

Introduction

The Nortel Call Recording Card installation pack contains the following 
items.

Table 7: 

Nortel Call Recording Card product structure

The 32-port media card comes with the dongle and the compact flash with 
the Nortel Call Recording Card load preinstalled (the C:/exec file on the 
Compact Flash card). Figure 4: “Media card layout,” on page 33 shows the 
layout of the Media Card.

Part #

NT Code

Description

A0888965

NTVQ01BA

32 port media card 

A0852632

A0852632

Shielded 50 pin key telephone to 9D sub and 
twin RJ45 adapter (L-Adapter)

A0870556

NTVQ83AA

ITG EMC shielding kit

A0783483

NTCW84JA

M1 backplane to 50-pin I/O panel cable 
(filter block)

N0056092

NT9S80MA

Compact flash with Nortel Call Recording 
Card application load

Security device (dongle)

Summary of Contents for Call Recording































































































Reviews:

No comments