background image

INSTALLATION / PERFORMANCE CHECKLIST

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Rated Voltage: ___________________________________ VOLTS

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct? 
(If Applicable)

YES

NO

REFRIGERATION SYSTEM

Was unit given 24 hr warm up period 
for crankcase heaters?

YES

NO

Stage-1 Liquid Pressure (high side) ________________________

Stage-1 Suction Pressure (low side) ________________________

INSTALLATION ADDRESS:

CITY ________________________

STATE ________________

UNIT MODEL # ________________________________________

UNIT SERIAL # ________________________________________

Unit Installed Minimum clearances per 

Figure 1, (page 3)

?

YES

NO

INSTALLER NAME:

CITY _______________________

STATE ________________

Has the owner’s information been 
reviewed with the customer?

YES

NO

Has the Literature Package been left 
with the unit?

YES

NO

7096810 (NEW)

PROPOSITION 65 WARNING:

WARNING: This product contains chemicals known 
to the state of California to cause cancer.

WARNING: This product contains chemicals known 
to the state of California to cause birth defects or 
other reproductive harm.

Specifications & illustrations subject to change 
without notice or incurring obligations (01/14).

REPLACEMENT PARTS

Replacement parts are available through all Nordyne 
distributors. Please have the complete model and serial 
number of the unit when ordering replacement parts.

Electrical:

•  Capacitors

•  Temperature Limit Switches

•  Compressors

•  Thermostats

•  Contactors

•  Time Delay Relays

•  Pressure Switches

•  Transformers

•  Relays

Motors:

•  Blower Motor
•  Fan Motor

Components:

•  Blower Assembly

•  Fan Grille

•  Cabinet Panels

•  Filter/Driers

•  Expansion Valves

Summary of Contents for T4BD-042 Series





















Reviews: