Safety
1-5
2014
Nordson Corporation
Issued 10-11
Maintenance and Repair Practices
Allow only personnel with appropriate training and experience to operate
or service the equipment.
Perform scheduled maintenance activities at the intervals described in
this document.
Relieve system hydraulic and pneumatic pressure before servicing the
equipment.
De‐energize the equipment and all auxiliary devices before servicing the
equipment.
Use only new Nordson‐authorized refurbished or replacement parts.
Read and comply with the manufacturer's instructions and the MSDS
supplied with equipment cleaning compounds.
NOTE:
MSDSs for cleaning compounds that are sold by Nordson are
available at www.nordson.com or by calling your Nordson representative.
Confirm the correct operation of all safety devices before placing the
equipment back into operation.
Dispose of waste cleaning compounds and residual process materials
according to governing regulations. Refer to the applicable MSDS or
contact the authority having jurisdiction for information.
Keep equipment safety warning labels clean. Replace worn or damaged
labels.
Equipment Safety Information
This equipment safety information is applicable to the following types of
Nordson equipment:
hot melt and cold adhesive application equipment and all related
accessories
pattern controllers, timers, detection and verification systems, and all
other optional process control devices
Summary of Contents for ProBlue P10
