43
6
APPENDIX A - INTERFACE CABLE MODIFICATION PROCEDURE
Some earlier models of John Deere sprayers
(4700 and 4710) may use a different style of
boom valve block with a different arrangement
of the connectors. As a result, the NORAC
44658-01 interface cable (C12) will need to be
modified according to the following instructions
(See
Figure 51
and
Figure 52
for before and
after schematics):
1.
Using the supplied GP Weatherpack pin
tool, carefully remove the blue/black wire
tee (Main Down) from the A-position of the
4-pin flat connector tee (S4B & T4B). The
blue wire is attached to a black wire that
goes across the tee connection (remove
both ends of this tee).
2.
Insert blue/black wire tee from step 1 into
the A-position of the 6-pin flat connectors,
M14 and M15 (S6C & T6C), that are
supplied in the zip lock bag with the cable
(these connectors are keyed on the A and F
position).
3.
Locate and remove the green wire (Left Up)
from the A-position of the 6-pin flat shroud
(S6B). Also remove the 5 black wires from
this tee (S6B & T6B). Use these 5 wires to
tee the remaining positions of the two 6-pin
connectors (S6C & T6C) used in step 2
together (B
B, C
C., D
D… etc).
Remove the cavity plug from the A-position
of T6B for use in step 4. After this step,
there will be 2 unused 6-pin flat connectors.
4.
Remove the black wire that goes across the
connection in the A-position of the 4-pin
square tee with the red wire (Right Up) in
the C-position (S4C & T4C). Insert the
green wire (Left Up) from step 3 into the A-
position of the 4-pin shroud (S4C). Seal the
A-position on the 4-pin tower (T4C) with
the cavity plug removed in step 3.
5.
Locate and remove the brown wire (Left
Down) from the A-position of the 6-pin flat
shroud (S6A). Remove the black wire that
goes across the connection in the A-position
of the 4-pin flat tee with the white wire
(Right Down) in the C-position (S4D &
T4D). Insert the brown wire (Left Down)
into the A-position of the 4-pin shroud
(S4D). A cavity plug will be removed in step
6 that may be used to seal the empty cavity
created when removing the black wire from
the 4-pin flat tower (T4D).
6.
Locate and remove the black wire (Main Up)
from the 4-pin square connector tee (S4A &
T4A). This black wire is attached to a black
tee wire similar to the wire described in
step 1. Insert black wire into the A-position
of the 6-pin flat assembly removed in step 5
(S6A & T6A). This will require removing the
cavity plug installed in the A-position of the
6-pin tower (T6A). The cavity plug can then
be used to seal the empty socket created in
step 5.
7.
The cable modifications are complete.
There should be 2 unused 6-pin flat
connectors, 2 black wires, an incomplete 4-
pin square tee and an incomplete 4-pin flat
tee left over.
8.
Connect the modified harness to the sprayer
as indicated in
Figure 53
.
Summary of Contents for UC4+
