Nokia NSW-5 Series Service Manual Download Page 48 | Manualshive

Page: 48 / 278

background image

NSW-5
System Module UT5U

PAMS Technical Documentation

Page 34

Issue 1 10/00

Nokia Mobile Phones Ltd.

800 MHz

Ext.

Standby

[mA]

800 MHz

Analog

Control

Channel

[mA]

800 MHz

Analog

Traffic

Channel

[mA]

800 MHz

Digital

Control

Channel

[mA]

800 MHz

Digital

Traffic

Channel

[mA]

1900 MHz

Digital

Control

Channel

[mA]

1900 MHz

Digital

Traffic

Channel

[mA]

VR1

9.0 / 0.0

9.0

9.0

9.0 / 0.0

9.0

19.0 / 0.0

19.0

VR2

16.0 / 0.0

16.0

16.0

16.0 / 0.0

16.0

0.0

0.0

VR3

0.0

0.0

23.0

0.0

13.0

0.0

8.0

VR4

11.6 / 0.0

11.6

11.6

32 / 0.0

12.8*

32 / 0.0

12.8*

VR5

0.0

0.0

37.0

0.0

13.0 **

0.0

13.0 **

VR6

2.0 / 0.1

2.0

32.0 ***

2.0 / 0.1

32.0 ***

2.0 / 0.1

32.0 ***

VR7

0.0

0.0

58.0

0.0

19.2 ’

0.0

0.0

VR8

19.0 / 0.0

19.0

19.0

19.0 / 0.0

7.6 ’’

0.0

0.0

VR9

0.0

0.0

0.0

0.0

0.0

30.0 / 0.0

12.0 ’’’

VR10

0.0

0.0

0.0

0.0

0.0

10.0 / 0.0

10.0

VR11

0.0

0.0

0.0

0.0

0.0

0.0

22.5^

VR12

0.0

0.0

0.0

0.0

0.0

0.0

12.9^^

V5V

5.0 / 0.0

5.0

5.0

5.0 / 0.0

5.0

5.0 / 0.0

5.0

Total

62.6 / 0.1

62.6

210.6

83.0 / 0.1

127.6

98.0 / 0.1

147.2

NOTES:

*

Mean value (ON/OFF=8/20ms), peak current 32.0 mA

** Mean value (ON/OFF=7/20ms), peak current 37.0 mA

*** Cobba_D mean current consumption estimated to be 30 mA

’ Mean value (ON/OFF=6.6/20ms), peak current 180.0 mA

’’ Mean value (ON/OFF=8/20ms), peak current 10.0 mA

’’’ Mean value (ON/OFF=8/20ms), peak current 15.0 mA when AGC2=1

^ Mean value (ON/OFF=6.6/20ms), peak current 68.0 mA

^^ Mean value (ON/OFF=6.6/20ms), peak current 39.0 mA

Regulators

Most of the RF voltage regulation functions are located in the regulator IC
CCONT. It has 8 separate regulators with power on/off controls (see fig
2). Regulator VR6 is used only for the COBBA_D IC and the rest of the
regulators VR1–VR7 are reserved for the RF blocks. VR7_bias controls
the 800MHz PA bias to boost better efficiency in analog mode and at
power levels 6 to 10 in digital mode. V5V voltage is used for the PLL
charge pump supply. In dual band phone there is a need for 5 additional
regulators, which are integrated in Penta regulator IC.

Receiver

DAMPS800 RX

The receiver is a double conversion receiver. Most of the RX functions
are integrated in two ICs, namely receiver front end and EROTUS. Re-
ceiver front end contains a LNA and the 1st mixer. Analog and digital IF–
parts are integrated in the EROTUS.

«
...
46
47
48
49
50
...
»

Summary of Contents for NSW-5 Series























































































































































































































































































Reviews:

No comments

Related manuals for NSW-5 Series

Brand: Unify Pages: 2

Brand: M2M Pages: 2

Brand: G53 Limited Pages: 10

Brand: Sagem Pages: 105

Brand: Bea-fon Pages: 70

Brand: Hyundai Pages: 24

Brand: Grandstream Networks Pages: 29

Brand: Gigaset Pages: 88

Brand: Wileyfox Pages: 58

Brand: Tadiran Telecom Pages: 11

Brand: myPhone Pages: 50

Brand: Karel Pages: 29

Brand: ION Pages: 24

Brand: Samsung Pages: 113

Brand: Samsung Pages: 201

Brand: Samsung Pages: 104

Brand: Samsung Pages: 128

SGH-T259 Series

Brand: Samsung Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands