manualshive.com logo in svg

Nimbra 300 Series, Installation And Maintenance Manual

Share
Download
Nimbra 300 Series Installation And Maintenance Manual Download Page 43

Installation and Maintenance Manual Nimbra 300 Series

Installation  

•

  41

©2006 Net Insight AB, All rights reserved

Caution:

Class 1 Laser Product.
Complies with 21 CFR 1040.10 and 1040.11

The optical ports must be terminated with an optical connector
or with a dust plug.

The use of optical instruments with this product will increase
eye hazard.

Note:

Avoid bending the optical cables more than the minimum bend
radius of 35 mm. A smaller radius could cause inadequate
signal levels or damage the cables.

Note the cable marking, to avoid swapping input and output
cables.

Handle only one cable at a time. Leave the protecting cap on all
connectors until immediately before connecting the cable.

Clean the cable connector using a standard fiber connector-
cleaning tool.

Connecting Optical Fibers to the SFP Module

Optical fibers are connected to the SFP module according to below.

•

 

Remove the protective cap from one of the cables and the connector on the SFP
module.

•

 

Insert the cable carefully in to the connectors of the SFP module and make sure
it is firm and fixed in place.

•

 

Repeat the procedure for the remaining connections to be made to the SFP
modules of the switch.

Summary of Contents for 300 Series




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands