manualshive.com logo in svg

Nimbra 300 Series, Installation And Maintenance Manual

Share
Download
Nimbra 300 Series Installation And Maintenance Manual Download Page 10

8  

•

  Contents

Installation and Maintenance Manual Nimbra 300 Series

©2006 Net Insight AB, All rights reserved

Key product features:

•

 

Bandwidth management with maximum network utilization

•

 

Service granularity and switching down to 0.5 Mbps

•

 

Guaranteed QoS independent of network load

•

 

Enhanced Ethernet functionality including service multiplexing

•

 

VLAN separation and user priority

•

 

End-to-end service provisioning using optical control plane

•

 

Comprehensive network re-routing and protection options

•

 

Unsurpassed multicast support maintaining QoS in any
network size or topology

The overall network is managed by the Nimbra Vision network management
system. Other management options include a built-in web GUI (Graphical User
Interface) for element management, CLI (Command Line Interface), and SNMP
(Simple Network Management Protocol).

The Nimbra 300 series of switches comes with an integrated control module and
a 5 Gbps non-blocking switch matrix. Apart from the fixed ports, the following
plug-in modules are available for mounting in the two horisontal slots:

•

 

OC-48/STM-16 X-ADM Module

•

 

1 Gbps Optical Trunk Module, LH and SH

•

 

OC-12/STM-4 Trunk Module

•

 

2 x OC-12/STM-4 Trunk Module

•

 

4 x OC-3/STM-1 Trunk Module

•

 

4 x DS3/E3 Trunk Module

•

 

Gigabit Ethernet Access Module

•

 

Fast Ethernet Access Module

•

 

SDI Video Access Module

•

 

ASI Transport Access Module

•

 

8 x ASI Transport Access Module

•

 

4 x OC-3/STM-1 Access Module

•

 

E1/T1 Access Modules

•

 

8 x AES/EBU Access Module

Summary of Contents for 300 Series




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands