Nilfisk-Advance CR 1500 Service Manual Download Page 94

Page: 94 / 147

Squeegee System

199

Service Manual – Advance 7765 / Nilfisk CR1500

Squeegee System Wiring Diagram

Circuit Description

The

Squeegee Lock Up (10)

solenoid valve blocks the bottom port on the squeegee deck cylinder to hold the

squeegee up in its retracted position when the machine is shut off.

•

When the key switch is on, the

Squeegee Lock Up (10)

solenoid valve is energized (open) to allow the

hydraulic oil to flow from the bottom port on the squeegee deck cylinder.

•

When the key switch is off, the

Squeegee Lock Up (10)

solenoid valve is de-energized (closed) to prevent the

hydraulic oil from flowing from the bottom port on the squeegee deck cylinder.

The

Squeegee Cylinder Solenoid (7)

controls the hydraulic oil flow to the squeegee deck cylinder.

•

When the

Squeegee Blade Switch

on the instrument panel is set to the squeegee-lower position (

Squeegee

Blade Switch

position

), the

Squeegee Cylinder Solenoid (7)

is de-energized to direct the hydraulic oil to the

top port on the squeegee deck cylinder to lower the squeegee.

•

When the

Squeegee Blade Switch

on the instrument panel is set to the squeegee-raise position (

Squeegee

Blade Switch

position

), the

Squeegee Cylinder Solenoid (7)

is energized to direct the hydraulic oil to the

bottom port on the squeegee deck cylinder to raise the squeegee.

•

When the drive pedal moves to the reverse position, the

Drive Pedal Reverse Sensor

switches to position

This energizes the

Reverse Relay

coil and switches the

Reverse Relay

to position

which:

– Energizes the

Squeegee Cylinder Solenoid (7)

through diode

to raise the squeegee, and,

– Provides positive voltage to the

Back-up Alarm

Note that diode

prevents the

Reverse Relay

from energizing the

Squeegee Fan Motor Solenoid (12).

This

allows the squeegee vacuum fan motor to continue to run when the machine is in reverse.

Also refer to the

Squeegee System Hydraulic Diagrams

section.

CB7

15 A

CB5

15 A

Squeegee Lock Up (10)

Battery 12 VDC

Bat.

Ignition

Switch

B-

Squeegee Fan Motor Solenoid (12)

Squeegee Cylinder Solenoid (7)

CB8

15 A

Squeegee

Blade Switch

Lower

Raise
(Traverse)

87a

Back-up Alarm

B-

Reverse Relay

Drive Pedal

Reverse Sensor

Summary of Contents for CR 1500




















































































































































Search results

Summary of Contents for CR 1500

Reviews:

Related manuals for CR 1500

Brands by name

Popular brands

Nilfisk-Advance CR 1500, Service Manual

Search results

Summary of Contents for CR 1500

Reviews:

Related manuals for CR 1500

Brands by name

Popular brands