manualshive.com logo in svg

Nilfisk-Advance CR 1500, Service Manual

Share
Download
Nilfisk-Advance CR 1500 Service Manual Download Page 96

Squeegee System 201

Service Manual – Advance 7765 / Nilfisk CR1500

Squeegee Up, Engine Running

When the engine is running and the squeegee blade switch is set to the squeegee-raise position, the 

Squeegee 

Lock Up (10)

 solenoid valve and 

Squeegee Cylinder Solenoid (7)

 are both energized. This directs the hydraulic 

oil to the bottom port on the 

Squeegee Deck Cylinder

 to raise the squeegee.

Note that the 

Squeegee Cylinder Solenoid (7)

 will also be energized to raise the squeegee when the drive pedal 

is moved to reverse and actuates the reverse relay.

C3

C4

C2

C1

1.02 

CIR

Check Valve 
270 PSI

Reservoir

Auxiliary 

Pump

8.2 GPM

1.5 GPM

Cylinder 
Control 
Valve

P

T

To Squeegee 

Vacuum Motor

Scrub Brush 

Solenoid (6)

Scrub Brush 

Solenoid (8)

Squeegee 

Cylinder 

Solenoid (7)

Squeegee 
Lock Up (10)

Scrub Brush 
Lock Up 
Solenoid (9)

Squeegee 

Deck 

Cylinder

To and From 
Scrub Deck 
Cylinder

Squeegee 

Up

Power 

Steering 

Unit

1500 

PSI

3.1 

CIR

P

T

Power Steering 

Cylinder

L

R

Summary of Contents for CR 1500




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands