Nilfisk-Advance CR 1500 Service Manual Download Page 47

Page: 47 / 147

Recovery System

152

Service Manual – Advance 7765 / Nilfisk CR1500

Component Locations

The following components are included in this section: Also refer to the

Solution System

section.

• Recovery Tank

• Recovery Tank Lid

• Drain Plug Assembly

• Recovery High (Float) Switch

• Drain Hose and Hose Holder

• Vacuum Motor and Fan Assembly

Recovery Tank

The

Recovery Tank

located on the front left-

hand side of the machine

and swings out away from

the machine for access and

cleaning.

The

Recovery Tank Lid

(cover assembly) houses

the vacuum motor

assembly, and swings up

for access to the

Recovery

Tank

Float Ball

and

Float

Ball Strap

Recovery

Tank Lid

Recovery

Tank

Float

Ball

Float Ball

Strap

Summary of Contents for CR 1500




















































































































































Search results

Summary of Contents for CR 1500

Reviews:

Related manuals for CR 1500

Brands by name

Popular brands

Nilfisk-Advance CR 1500, Service Manual

Search results

Summary of Contents for CR 1500

Reviews:

Related manuals for CR 1500

Brands by name

Popular brands