FORM NO. 56043051 / Retriever
™
2060 - 55
HYDRAULIC SYSTEM
FRONT
M
G
E
O
F
N
P
H
J
L
Q
K
B
C
A
D
I
S
R
6
If the drive wheel moves, loosen the two connector Nuts (D) and adjust the cable until the drive wheel does not move in the neutral
position.
7
Tighten the two connector Nuts (D) and test for proper operation.
FIGURE 7
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
HOPPER UP CONTROL CABLE REPLACEMENT
NOTE: Have hopper in raised position.
WARNING!
Make sure hopper is securely supported before working under hopper.
1
Open the left side front service door then lift and move circuit breaker assembly to access cable.
2
Loosen the two lower connector Nuts (L) and pull the cable from mounting bracket.
3
Remove the two Bolts (M) and remove the Pivot Block (N).
4
Move the Actuator (O) to the right and remove it from the Interlock Bracket (P).
5
Remove Ball Joint (Q) from the Actuator (O), then unthread the ball joint from the cable end.
6
Loosen the two upper connector Nuts (R) and pull the cable from the mounting bracket.
7
Remove the upper Ball Joint (S) from the hopper weldment and unthread it from the cable end.
8
Pull the cable through the channel. NOTE: If installing a new cable, tape it to the old cable end and use the old cable to feed the
new cable through channel.
9
Install new cable in reverse order.
10
Adjust the two lower connector nuts so Actuator (O) does not interfere with the propulsion pump arm when moving the foot pedal
forward and reverse.
11
Test for proper operation by raising the hopper and ensuring the upper portion of the actuator moves to the right.
12
After replacing the cable follow the steps in the Hopper up control cable adjustment section.
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
HYDROBACK DRIVE PEDAL NEUTRAL ADJUSTMENT (CONTINUED)
Summary of Contents for Advance Retriever 2060
