background image

EDH0316En1031 — 11/18                                                                                                   

ii

ZVR Series                                     Integrated Vertical and Rotation Stages for Wafer Positioning

Warranty

Newport Corporation warrants this product to be free from defects in

material and workmanship for a period of 1 year from the date of

shipment. If found to be defective during the warranty period, the product

will either be repaired or replaced at Newport’s discretion.

To exercise this warranty, write or call your local Newport representative,

or contact Newport headquarters in Irvine, California. You will be given

prompt assistance and return instructions. Send the instrument,

transportation prepaid, to the indicated service facility. Repairs will be

made and the instrument returned, transportation prepaid. Repaired

products are warranted for the balance of the original warranty period, or

at least 90 days.

Limitation of Warranty

This warranty does not apply to defects resulting from modification or

misuse of any product or part.

This warranty is in lieu of all other warranties, expressed or implied,

including any implied warranty of merchantability or fitness for a

particular use. Newport Corporation shall not be liable for any indirect,

special, or consequential damages.

             by Newport Corporation, Irvine, CA. All rights reserved.

Original instructions.

No part of this document may be reproduced or copied without the prior

written approval of Newport Corporation. This document is provided for

information only, and product specifications are subject to change without

notice. Any change will be reflected in future publishings.

CAUTION

Warranty does not apply to damages resulting from:

• Incorrect usage:

– Load on the stage greater than maximum specified load.

– Carriage speed higher than specified speed.

– Improper grounding.

¬ Connectors must be properly secured.

¬ When the load on the stage represents an electrical risk, it must

be connected to ground.

– Excessive or improper cantilever loads.

• Modification of the stage or any part thereof.

CAUTION

Please return equipment in
the original (or equivalent)
packing.

You will be responsible for
damage incurred from
inadequate packaging if the
original packaging is not

used.

© 2018

Summary of Contents for ZVR Series



























Reviews:

Related manuals for ZVR Series