background image

Page 26 

NX1348E Icon Keypad 

One will be the normal exit from the building.  The other may be a window that opens 
easily.  An escape ladder may have to be located near the window if there is a long 
drop to the ground below.  Set a meeting place outdoors for a headcount of the 
building occupants.  

Practice escape procedures. In a home, sleep with bedroom door closed; this will 
increase your escape time.  If you suspect fire, test the door for heat.  If you think it is 
safe, brace your shoulder against the door and open it cautiously.  Be ready to slam 
the door if smoke or heat rush in.  Practice escaping to the outdoors and meeting in 
an assigned spot.  Call the Fire Department from a neighbor's phone. NOTE:  After 
the installation of your Security System has been completed, notify your local Fire 
and Police Departments to give them your name and address for their records.  Early 
warning fire detection is best achieved by the installation of fire detection equipment 
in all rooms.  This equipment should be installed in accordance with the National Fire 
Protection Association's Standard 72. For additional information write the National 
Fire Protection Association, Batterymarch Park, Quincy, MA 02269. 

The following are examples of evacuation plans.  A plan unique to your home or 
business should be drawn and memorized by each occupant. 

Summary of Contents for NX-1348E





























Reviews: