Netopia R7200 User Reference Manual Download Page 22

Page: 22 / 258

3-4 User’s Reference Guide

Netopia R7200 SDSL Router status lights

The figure below represents the Netopia R7200 status light (LED) panel.

Netopia R7200 LED front panel

The following table summarizes the meaning of the various LED states and colors:

When this happens...

the LEDs...

The WAN inter face is operational

3 is

green

The line is unavailable

3 flashes

red

The WAN has carrier

4 is

green

Data is transmitted or received on the WAN

4 flashes

yellow

Carrier is asser ted

6 and 7 are

green

Data is transmitted or received

6 and 7 flash

yellow

Data is transmitted or received by the ethernet controller

12 flashes

yellow

The Ethernet inter face detects a collision

13 flashes

red

Link is detected

14 though 21 are

solid green

Data are received on their respective por ts

14 though 21

flash green

Note:

5 and 8 through 11 are unused, since the SDSL link is carried only on WAN channel 1. Also, Console

carrier (6) is ignored if the console is not configured for a remote modem.

2 3 4 5

6 7

8 9 10 11

12 13 14 15 16171819 20 21

Management

Ready

Channel 1

Link/Receive

Console

Auxiliar

Collision

Traffic

WAN 1

WAN 2

Ethernet

Power

Channel 2

Management

Ready

Channel 1

Channel 2

Summary of Contents for R7200



































































































































































































































































Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands

Netopia R7200, User Reference Manual

Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands