Netopia R7200 User Reference Manual Download Page 187

Page: 187 / 258

Utilities and Diagnostics 15-1

haa

pttttee

errrr 11115

Uttttiiiilllliiiittttiiiiee

essss aa

d D

Diiiiaa

ossssttttiiiiccccssss

A number of utilities and tests are available for system diagnostic and control purposes.

This section covers the following topics:

■

“Ping” on page 15-2

■

“Trace Route” on page 15-4

■

“Telnet client” on page 15-5

■

“Disconnect Telnet console session” on page 15-6

■

“Factor y defaults” on page 15-6

■

“Transferring configuration and firmware files with TFTP” on page 15-7

■

“Transferring configuration and firmware files with XMODEM” on page 15-9

■

“Restar ting the system” on page 15-12

Note:

These utilities and tests are accessible only through the console-based management screens. See

Chapter 6, “Console-Based Management,”

for information on accessing the console-based management

screens.

You access the Utilities & Diagnostics screens from the Main Menu.

Utilities & Diagnostics

Ping...
Trace Route...
Telnet...

Disconnect Telnet Console Session...

Trivial File Transfer Protocol (TFTP)...
X-Modem File Transfer...

Revert to Factory Defaults...

Restart System...

Summary of Contents for R7200



































































































































































































































































Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands

Netopia R7200, User Reference Manual

Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands