Netopia R7200 User Reference Manual Download Page 142

Page: 142 / 258

13-12 User’s Reference Guide

System Information

The System Information screen gives a summar y view of the general system level values in the Netopia R7200
SDSL Router.

From the Statistics & Logs menu select

System Information

. The System Information screen appears.

The information display varies by model, firmware version, feature set, and so on. You can tell at a glance your
par ticular system configuration.

SNMP

The Netopia R7200 includes a Simple Network Management Protocol (SNMP) agent, allowing monitoring and
configuration by a standard SNMP manager.

The Netopia R7200 suppor ts the following management information base (MIB) documents:

■

MIB II (RFC 1213)

■

Inter face MIB (RFC 1229)

■

Ethernet MIB (RFC 1643)

■

AppleTalk MIB I (RFC 1243)

■

Netopia MIB

These MIBs are on the Netopia R7200 CD included with the Netopia R7200. Load these MIBs into your SNMP
management software in the order they are listed here. Follow the instructions included with your SNMP
manager on how to load MIBs.

System Information

Serial Number 70-02-ec (7340780)
Firmware Version 4.3

Processor Speed (MHz) 33
Flash ROM Capacity (MBytes) 1
DRAM Capacity (MBytes) 4

Ethernet 8 Port 10Base-T
Auxiliary Serial Port Switched Async
WAN 1 Interface SDSL
WAN 2 Interface Not Installed

AppleTalk Feature Set Installed
User Restriction (# users) 13
Analog Dial-In Kit Installed

Summary of Contents for R7200



































































































































































































































































Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands

Netopia R7200, User Reference Manual

Search results

Summary of Contents for R7200

Reviews:

Related manuals for R7200

Brands by name

Popular brands