Netopia R7200 User Reference Manual Download Page 169 | Manualshive

Page: 169 / 258

background image

Security 14-19

Basic Firewall is suitable for a LAN containing only client hosts that want to access ser vers on the WAN, but not
for a LAN containing ser vers providing ser vices to clients on the WAN. Basic Firewall’s general strategy is to
explicitly for ward WAN-originated TCP and UDP traffic to por ts greater than 1023. Por ts lower than 1024 are the
ser vice origination por ts for various Internet ser vices such as FTP, Telnet, and the World Wide Web (WWW).

A more complicated filter set would be required to provide WAN access to a LAN-based ser ver. See the next
section,

“Possible modifications,”

for ways to allow remote hosts to use ser vices provided by ser vers on the

LAN.

Possible modifications

You can modify the sample filter set Basic Firewall to allow incoming traffic using the examples below. These
modifications are not intended to be combined. Each modification is to be the only one used with Basic Firewall.

The results of combining filter set modifications can be difficult to predict. It is recommended that you take
special care if you are making more than one modification to the sample filter set.

Trusted host.

To allow unlimited access by a trusted remote host with the IP address a.b.c.d (corresponding to

a numbered IP address such as 163.176.8.243), inser t the following input filter ahead of the current input
filter 1:

■

Enabled: Yes

■

For ward: Yes

■

Source IP Address: a.b.c.d

■

Source IP Address Mask: 255.255.255.255

■

Dest. IP Address: 0.0.0.0

■

Dest. IP Address Mask: 0.0.0.0

■

Protocol Type: 0

Trusted subnet.

To allow unlimited access by a trusted remote subnet with subnet address a.b.c.d

(corresponding to a numbered IP address such as 163.176.8.0) and subnet mask e.f.g.h (corresponding to a
numbered IP mask such as 255.255.255.0), inser t the following input filter ahead of the current input filter 1:

■

Enabled: Yes

■

For ward: Yes

■

Source IP Address: a.b.c.d

■

Source IP Address Mask: e.f.g.h

■

Dest. IP Address: 0.0.0.0

■

Dest. IP Address Mask: 0.0.0.0

■

Protocol Type: 0

«
...
167
168
169
170
171
...
»

Summary of Contents for R7200



































































































































































































































































Reviews:

No comments

Related manuals for R7200

Verizon DSL-2750B

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: DataRemote Pages: 2

Brand: iDirect Pages: 60

Module NI PXI-8250

Brand: National Instruments Pages: 39

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 23

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

DiamondLink 3201

Brand: Patton Pages: 12

Ezi-SERVOII EtherCAT TO

Brand: Fastech Pages: 108

Brand: Global411 Pages: 15

Brand: iGateWeb.com Pages: 6

Brand: Axis Pages: 98

Brand: Maipu Pages: 19

Ether-GSH24T v3

Brand: AirLive Pages: 2

Dimension GS-2024

Brand: ZyXEL Communications Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands