NETGEAR Orbi User Manual Download Page 112

Page: 112 / 124

Use VPN to Access Your Network

112

Orbi High-Performance

AC3000

Tri-band

WiFi

System

Select the

Enable VPN Service

radio button.

Scroll down to the Clients will use this VPN connection to access section, and select the

Home Network only

radio button.

This is the default setting.The VPN connection is only to your home network, not to the
Internet service for your home network.

Click the

Apply

button.

Your settings are saved.

Click the

FOR WINDOWS

FOR MAC0SX

button and download the configuration files for

your VPN clients.

Unzip the configuration files and copy them to the folder where the VPN client is installed on

your device.

For a client device with Windows 64-bit system, the VPN client is installed at

C:\Programfiles\OpenVPN\config\

by default.

Use a VPN Tunnel to Access Your Internet Service at Home



To access your Internet service:

Set up the router to allow VPN access to your Internet service.

See

Specify VPN Service in the Router

on page

103.

On your computer, launch the OpenVPN application.

The OpenVPN icon displays in the Windows taskbar.

Right-click the icon and select

Connect

When the VPN connection is established, launch your Internet browser.

Summary of Contents for Orbi





























































































































Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands

NETGEAR Orbi, User Manual

Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands