NETGEAR Orbi User Manual Download Page 111

Page: 111 / 124

Use VPN to Access Your Network

111

Orbi High-Performance

AC3000

Tri-band

WiFi

System

Enter the router user name and password.

The user name is

admin

. The default password is

password

. The user name and

password are case-sensitive.

The BASIC Home page displays.

Select

ADVANCED > Advanced Setup > VPN Service

The VPN Service page displays.

Select the

Enable VPN Service

radio button.

Scroll down to the Clients will use this VPN connection to access section, and select the

All

sites on the Internet & Home Network

radio button.

When you access the Internet with the VPN connection, instead of using a local Internet
service, you use the Internet service from your home network.

Click the

Apply

button.

Your settings are saved.

Click the

FOR WINDOWS

FOR MACOSX

button and download the configuration files for

your VPN clients.

Unzip the configuration files and copy them to the folder where the VPN client is installed on

your device.

For a client device with Windows 64-bit system, the VPN client is installed at

C:\Programfiles\OpenVPN\config\

by default.

Block VPN Client Internet Access in the Router

By default, the router is set up to allow VPN connections only to your home network, not to
the Internet service for your home network. If you changed this setting to allow Internet
access, you can change it back.



To allow VPN clients to access only your home network:

Launch a web browser from a WiFi-enabled computer or mobile device that is

connected to the network.

Enter

orbilogin.com

A login window opens.

Enter the router user name and password.

The user name is

admin

. The default password is

password

. The user name and

password are case-sensitive.

The BASIC Home page displays.

Select

ADVANCED > Advanced Setup > VPN Service

The VPN Service page displays.

Summary of Contents for Orbi





























































































































Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands

NETGEAR Orbi, User Manual

Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands