NETGEAR Orbi User Manual Download Page 10

Page: 10 / 124

Overview

Orbi High-Performance

AC3000

Tri-band

WiFi

System

Optional Orbi Add-On Satellite LEDs

You can purchase add-on Orbi satellites (sold separately) and add them to your Orbi network.

Table 2. Orbi Add-On Satellite LED description

LED

LED Behavior

Power

The Power LED is located above the

Power On/Off

button on the rear

panel.

•

Solid green

.Power is on.

•

Solid amber

. The satellite is rebooting.

•

Blinking amber

. Resetting to factory default settings.

•

Blinking red

. The firmware is corrupted.

•

Off

. Power is not supplied.

Add-On Satellite ring

Optional Add-On Satellites are sold separately and can be added on to your
Orbi network. The ring LED is located on the top.

•

Pulsing white

. The satellite is booting.

•

Solid white

. The satellite is ready to sync to the router (press the

Sync

button).

•

Blue for 3 minutes

. The connection between the satellite and the

router is good.

•

Amber for 3 minutes

. The connection between the satellite and the

router is fair.

•

Magenta

. The satellite is not connected to the router or is not getting an

IP address.

•

Off

. The satellite synced to the router and is working normally.

Connect Your Router



To cable your router:

Unplug your modem’s power, leaving the modem connected to the wall jack for your

Internet service.

If your modem uses a battery backup, remove the battery.

Plug in and turn on your modem.

If your modem uses a battery backup, put the battery back in.

Summary of Contents for Orbi





























































































































Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands

NETGEAR Orbi, User Manual

Search results

Summary of Contents for Orbi

Reviews:

Related manuals for Orbi

Brands by name

Popular brands