NEC VERSA 6220 - SERVICE Service And Reference Manual Download Page 67

Page: 67 / 130

Setup and Operation 2-27

Looking at Screens

Setup screens have three areas as shown next.

AMIBIOS SETUP – ADVANCED CMOS SETUP

Plug and Play Aware O/S

Auto

BootUp USB Configuration

Disabled

Bootup Sequence

A:,C:

Docking Station Video

Dock Stn.

BootUp Num–Lock

Auto

LCD Panel View Expansion

Off

Password Check

Setup

Select the boot configuration

of AMIBIOS. Yes indicates

the system will boot to a

Plug and Play aware Operating

System such as Windows

95(tm). When set to Auto,

the system will detect Plug

and Play OS’s.

:Exit :Sel

:Modify

:Color

Figure 2-20 Advanced CMOS Setup Menu

Parameters
The left part of the screen. This area lists parameters and their current settings.

Available Options
The right part of the screen. This area lists and explains alternate settings.

Key Legend
The bottom right corner of the screen. These lines display the keys that move the
cursor and select parameters.

SOLD BY laptopia2005 DO NOT RESELL!!

Summary of Contents for VERSA 6220 - SERVICE



































































































































Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands

NEC VERSA 6220 - SERVICE, Service And Reference Manual

Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands