NEC VERSA 6220 - SERVICE Service And Reference Manual Download Page 7

Page: 7 / 130

iv Contents

256K X Flash ROM .............................................................................................. 1-19

ROM BIOS.................................................................................................... 1-19

VGA Controller .................................................................................................... 1-19

Parallel Interface ...................................................................................................1-20

Keyboard Controller .............................................................................................1-20

PC CardBus Controller ......................................................................................... 1-20

Sound Integrated Circuit ....................................................................................... 1-20

Interrupt Controllers .............................................................................................1-21

Power Management Overview ..................................................................................... 1-22

System Power Management .................................................................................. 1-23

Local Power Management..................................................................................... 1-23

Plug and Play............................................................................................................... 1-24

Specifications............................................................................................................... 1-25

Section 2 Setup and Operation

Unpacking the System.................................................................................................. 2-1

Hardware Setup ........................................................................................................... 2-1

Cable Connections ................................................................................................ 2-3

Power Sources............................................................................................................. 2-4

Using the AC Adapter........................................................................................... 2-4

Using the Main Battery Pack................................................................................. 2-5

Checking Battery Power Levels......................................................................2-5

What to Do When Battery Power Gets Low................................................... 2-6

Returning the Battery to Full Operation.......................................................... 2-6

When to Change the Battery .......................................................................... 2-6

Battery Handling ............................................................................................2-6

Replacing the Battery Pack ............................................................................ 2-7

Battery Precautions ........................................................................................ 2-10

Recharging Battery Precautions......................................................................2-10

NEC VersaBay II Battery and Adapter Kit ............................................................ 2-11

Extending Battery Life .......................................................................................... 2-11

Using the DC Car Adapter .................................................................................... 2-11

Operating Controls ...................................................................................................... 2-12

LCD Status Bar .................................................................................................... 2-13

Status Icons ................................................................................................... 2-13

Function Keys (Fn Keys).......................................................................................2-14

Smart Power Switch .............................................................................................2-14

SOLD BY laptopia2005 DO NOT RESELL!!

Summary of Contents for VERSA 6220 - SERVICE



































































































































Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands

NEC VERSA 6220 - SERVICE, Service And Reference Manual

Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands