NEC VERSA 6220 - SERVICE Service And Reference Manual Download | Manualshive

Page: 56 / 130

background image

2-16 Setup and Operation

Switch 3 — Reserved for factory use.

Switch 4 — Reserved for factory use.

Switch 5 — Not used.

Switch 6 — Reserved for factory use.

Updating the System BIOS

Use the following steps to update your NEC Versa 6220/30/60 system BIOS with the BIOS
Update Diskette (BUD). Specifically, the BIOS is the code transmitted onto your system’s
microprocessor, or central processing unit (CPU).

NOTE

You only need to update the BIOS if NEC

makes significant improvements or fixes to the
current system BIOS. Your authorized NEC
dealer or Technical Support Services representa-
tive can help you determine this.

If you are informed that the default BIOS needs an upgrade, to receive a copy of the BUD
contact the NECCSD Diskette Fulfillment Center at (800) 842-6446, or NECCSD Cus-
tomer Service and Technical Support at (800) 632-4525, Fax (978) 635-4100.

You should only use the BIOS upgrade diskette for your specific model.

NOTE

If you purchased and are using this com-

puter outside the U.S. or Canada, please contact
a local NEC office or dealer in your country.

Updating the BIOS involves the following procedures:

removing the speaker caps

lifting and moving the keyboard out of the way

setting the switch

reassembling the unit and updating the BIOS

resetting the switch.

SOLD BY laptopia2005 DO NOT RESELL!!

SOLD BY laptopia2005 DO NOT RESELL!!

«
...
54
55
56
57
58
...
»

Summary of Contents for VERSA 6220 - SERVICE



































































































































Reviews:

No comments

Related manuals for VERSA 6220 - SERVICE

Toughbook CF-U1AQB1G2M

Brand: Panasonic Pages: 60

Brand: IBM Pages: 142

Brand: Core Innovations Pages: 26

TravelMate 5335

Brand: Acer Pages: 313

TravelMate 5740

Brand: Acer Pages: 314

Extensa 5430 Series

Brand: Acer Pages: 176

MX6440 - Notebook Computer

Brand: Gateway Pages: 1

Brand: Fujitsu Pages: 18

T4310 - LifeBook Tablet PC

Brand: Fujitsu Pages: 2

A205-S4797 - Satellite - Core 2 Duo 1.73 GHz

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 5

Brand: Toshiba Pages: 5

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands