NEC VERSA 6220 - SERVICE Service And Reference Manual Download

Page: 82 / 130

3-6 Troubleshooting

Table 3-3 Beep Codes

Number of Beeps

Error

Description

Refresh Failure

The memory refresh circuitry on the
motherboard is faulty.

Parity Error

Parity error in the first 64 KB of memory.

Base 64 KB Memory
Failure

Memory failure in the first 64 KB.

Timer Not Operational

Memory failure in the first 64 KB of memory
or Timer 1 on the motherboard is not
functioning.

Processor Error

The CPU on the motherboard generated an
error.

Gate A20 Failure

The keyboard controller may be bad. The
BIOS cannot switch to protected mode.

Processor Exception
Interrupt Error

The CPU generated an exception interrupt.

Display Memory
Read/Write Error

The system video adapter is either missing
or its memory is faulty. (This is not a fatal
error.)

ROM Checksum Error

The ROM checksum value does not match
the value encoded in the BIOS.

CMOS Shutdown
Register Read/Write
Error

The shutdown register for CMOS RAM
failed.

Cache Error/External
Cache Bad

The external cache is faulty.

SOLD BY laptopia2005 DO NOT RESELL!!

Summary of Contents for VERSA 6220 - SERVICE



































































































































Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands

NEC VERSA 6220 - SERVICE, Service And Reference Manual

Search results

Summary of Contents for VERSA 6220 - SERVICE

Reviews:

Related manuals for VERSA 6220 - SERVICE

Brands by name

Popular brands