background image

Troubleshooting      3-5

 Table 3-2   POST Error Messages (cont’d)

 Message

 What To Do

 FDD Controller
Failure

The BIOS cannot communicate with the floppy disk controller.
Contact your NECCSD service representative to check all
appropriate connections.

 HDD Controller
Failure

 The BIOS cannot communicate with the hard disk drive controller.
Contact your NECCSD service representative to check all
appropriate connections.

 INTR #1 Error

 Interrupt channel 1 failed POST. Contact your NECCSD service
representative for service.

 INTR #2 Error

 Interrupt channel 2 failed POST. Contact your NECCSD service
representative for service.

 Invalid Boot Diskette

 The BIOS can read the diskette in drive A:, but cannot boot the
computer. Use another boot diskette.

 Keyboard is Locked
Unlock It

 The keyboard lock on the computer is engaged. The computer
must be unlocked to continue.

 Keyboard Error

 There is a timing problem with the keyboard. Set the Keyboard
option in Setup to Not Installed to skip the keyboard POST
routines.

 KB\interface error

 There is an error in the keyboard connector. Contact your
NECCSD service representative for service.

 Off Board parity Error

 Parity error installed in an expansion slot. Contact your NECCSD
service representative to be sure that the memory module is
installed correctly.

 The error format is:
OFF BOARD PARITY ERROR
ADDR(HEX) = (XXXX)
XXXX is the hex address where the error occurred.

 On Board Parity Error

 Parity error in system board memory. Contact your NECCSD
service representative for service.

 Parity Error ????

 Parity error in system memory at an unknown address. Contact
your NECCSD service representative for service.

 

Fatal errors that occur during POST are communicated through a series of beeps. All beep
code errors, except beep code 8, are fatal errors and do not allow the system to continue to
boot.

If beep codes occur during POST, check the items in the Problem Checklist (at the start of
this chapter), verify that all the hardware is set up properly and securely connected, and try
rebooting. If you still get a beep code, go to the section “If You Need Assistance” at the
end of this chapter.

Beep Codes are listed in the table that follows.

SOLD BY laptopia2005 DO NOT RESELL!!

SOLD BY laptopia2005 DO NOT RESELL!!

Summary of Contents for VERSA 6220 - SERVICE



































































































































Reviews: