manualshive.com logo in svg

NEC V850E/CA1 ATOMIC, Preliminary User'S Manual

The NEC V850E/CA1 ATOMIC Preliminary User's Manual is available for free download from manualshive.com. This comprehensive manual provides essential instructions and information on efficiently operating the product. Accessible in a user-friendly format, it ensures an optimal user experience when interacting with the NEC V850E/CA1 ATOMIC.

Share
Download
background image

192

Chapter 7

Interrupt/Exception Processing Function

Preliminary User’s Manual U14913EE1V0UM00

7.2.2 Restore

(1)

NMIVC

Execution is restored from the non-maskable interrupt (NMIVC) processing by the RETI instruction.
When the RETI instruction is executed, the CPU performs the following processing, and transfers 
control to the address of the restored PC. 

<1>Restores the values of the PC and the PSW from FEPC and FEPSW, respectively, because the EP

bit of the PSW is 0 and the NP bit of the PSW is 1.

<2>Transfers control back to the address of the restored PC and PSW.

Figure 7-4 illustrates how the RETI instruction is processed. 

Figure 7-4:  RETI Instruction Processing

Caution:  When the PSW.EP bit and PSW.NP bit are changed by the LDSR instruction during 

non-maskable interrupt processing, in order to restore the PC and PSW correctly dur-
ing recovery by the RETI instruction, it is necessary to set PSW.EP back to 0 and 
PSW.NP back to 1 using the LDSR instruction immediately before the RETI instruc-
tion.

Remark:

 The solid line indicates the CPU processing flow.

(2)

NMIWDT

Restoring by RETI instruction is not possible. Perform a system reset after interrupt servicing.

PSW.EP

RETI instruction

PSW.NP

Original processing restored

1

1

0

0

PC

PSW

EIPC

EIPSW

PC

PSW

FEPC

FEPSW

Summary of Contents for V850E/CA1 ATOMIC


























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V850E/CA1 ATOMIC

Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Brand: Hanna Instruments Pages: 88
Eaton Cutler-Hammer Jockey Instructions Manual preview
Cutler-Hammer Jockey
Brand: Eaton Pages: 12
Eaton C22- P Series Instruction Leaflet preview
C22- P Series
Brand: Eaton Pages: 2
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Brand: AGRI TRONIX Pages: 26
TAC Vista TAC Xenta OP Manual preview
TAC Xenta OP
Brand: TAC Vista Pages: 2
Ellard V3D Maxi Product Instructions preview
V3D Maxi
Brand: Ellard Pages: 21
J+J J4C B140 Handbook preview
J4C B140
Brand: J+J Pages: 91
Walchem WCT400 Series Instruction Manual preview
WCT400 Series
Brand: Walchem Pages: 43
S2Tech 699PLUS Instruction Manual preview
699PLUS
Brand: S2Tech Pages: 4
ELMARK CD-701 Instructions For Installation And Use Manual preview
CD-701
Brand: ELMARK Pages: 7
DAV TECH DAT 096 Installation And Maintenance Manual preview
DAT 096
Brand: DAV TECH Pages: 22
Watlow Anafaze PPC-2000 User Manual preview
Anafaze PPC-2000
Brand: Watlow Pages: 320
LEGRAND Arteor Instructions preview
Arteor
Brand: LEGRAND Pages: 2
Kemper 689 04 011 Service Manual preview
689 04 011
Brand: Kemper Pages: 16
Addonics Technologies ADN1GPX Specification & Installation Manual preview
ADN1GPX
Brand: Addonics Technologies Pages: 1
Infineon Technologies XE166 Hardware Manual preview
XE166
Brand: Infineon Technologies Pages: 28
Pentair Goyen IS Series Products Installation Instructions preview
Goyen IS Series
Brand: Pentair Pages: 6
Warner Electric slo-syn 440 Installation Instructions Manual preview
slo-syn 440
Brand: Warner Electric Pages: 16

Brands by name

Popular brands

Load more brands