manualshive.com logo in svg

NEC Univerge UM8000, Installation Manual

Share
Download
NEC Univerge UM8000 Installation Manual Download Page 22

Issue No. 1.0

UM8000

2 - 4

WinSCP and PuTTY

To install the PuTTY, perform the following procedure: 

1.

Insert the 

Support

 disc into the disk drive. 

The autostart page appears. 

2.

Using Windows Explorer, go to the 

Utilities/RemoteAccess/Putty/

 directory. 

3.

Double-click 

putty-0.59-installer.exe

 to start the PuTTY installation. 

An Open File security alert message appears. 

4.

Click 

RUN

.

The Welcome to the PuTTY Setup Wizard appears. 

5.

Click 

Next

. 

The Select Destination Location page appears. 

6.

Accept the default installation path or type a new path, then click 

Next

.

The Select Start menu folder page appears. 

7.

Accept the default components, if appropriate, choose a language for 
translation, then click 

Next

.

8.

Accept the default 

Start Menu

 folder name or type a new name, then click 

Next

.

9.

The Select Additional Tasks page appears. 

10.

Select the appropriate tasks to complete, then click 

Next

.

The Ready to Install page appears. 

11.

Verify that the settings are correct, then click 

Install

. 

To review or change any of the settings, click 

Back

. 

12.

Clear the 

View README.txt

 check box, then click 

Finish

.

3.2

Configuring PuTTY

To configure PuTTY, perform the following procedure:

1.

On the Windows taskbar, click 

Start > Programs > PuTTY > PuTTY

. 

The PuTTY Configuration page appears.

2.

Use a network crossover cable to connect the voice board to a computer. 

3.

Type in the Host Name (or IP address) field. 

The IP address for the voice mail is assigned in chassis programming 10-
55-xx.  At default this address is 172.16.1.xxx, where .xxx will vary 
depending upon which slot the CD-VM00 was installed.  Starting with slot 
1 this will be .100, slot 2 will be .101, slot 5 will be .104 and so on.

4.

Click 

Open

. 

When the first connection is made, a warning message appears. The 

Summary of Contents for Univerge UM8000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands