NEC UNIVERGE SL2100, Networking Manual

Page: 133 / 196

Program
Number
Program Name Description/Comments Assigned Data 1 2 3
84-23-05 DT800/DT700 Multiline
Basic Information Set-
up – Invite Expire Timer When INVITE message received from
SIP MLT does not contain Expires
header, the CPU uses this value for
timeout of outgoing call. E.g. The SIP
MLT hears RBT for duration of this
timer and then is disconnected. Range: 0~65535 Sec.
Default is 180 X
84-23-06 DT800/DT700 Multiline
Basic Information Set-
up – Signal Type of
Service Used for updating the IP terminals
SIGNALING TOS values.
Range: 0x00 ~ 0xFF
Default is 00 X
84-23-07 DT800/DT700 Multiline
Basic Information Set-
up – Error Display Tim-
er The time that an IP terminal holds an
error message in the display. Setting 0
holds the error message indefinitely. Range: 0 ~ 65535 Sec.
Default is 0 X
84-23-08 DT800/DT700 Multiline
Basic Information Set-
up – Digest Authoriza-
tion Registration Expire
Timer When Digest Authentication mode is
ON, this value is available.
After receiving Initial INVITE without
authentication information, CPU will
send 401 message to the SIP MLT,
then waits for an INVITE message
with the authentication message from
SIP MLT within this timer.
Additionally, after receiving Re-REG-
ISTER message for Keep Alive pur-
pose, the CPU sends a 401 message. Range: 0 ~ 4294967295
Default is 0 X
84-23-10 DT800/DT700 Multiline
Basic Information Set-
up – Number of Pass-
word Retries The number of times an incorrect
password can be entered when the
security key is pressed.
If set to (1), only one attempt is al-
lowed. When number of password re-
tries is met an error message displays
on the phone: Incorrect security code
password entered, press call key to
contact an administrator Range: 0 ~ 255
Default is 0 X
84-23-11 DT800/DT700 Multiline
Basic Information Set-
up – Password Lock
Time Time to leave the terminal Locked Out
after entering the wrong security code. Range; 0 ~ 120
Default: 0
Default is 0 X
84-23-12 DT800/DT700 Multiline
Basic Information Set-
up – Reference Num-
ber Assign the network admin telephone
number. When the user presses the
Call key to contact the network admin-
istrator, this number is dialed. Up to 32 Digits
(0~9, *, #, P, R, @)
Default is No Setting X
84-23-13 DT800/DT700 Multiline
Basic Information Set-
up – Media Type of
Service Assign the IP terminals MEDIA TOS
values.
Range: 0x00 ~ 0xFF
(0~9, A~F)
Default is 00 X
84-23-14 DT800/DT700 Multiline
Basic Information Set-
up – Refer Expire Tim-
er The valid period of the REFER sub-
scription. Range: 0 ~ 65535 Sec.
Default is 60 X
84-24-01 DT800/DT700 Multiline
CODEC Basic Informa-
tion Setup – Number of
G.711 Audio Frames Amount of audio in each RTP packet. Range: 1~4
1 = 10ms
2 = 20ms
3 = 30ms
4 = 40ms
Default is 2 X
84-24-02 DT800/DT700 Multiline
CODEC Basic Informa-
tion Setup - G.711 Si-
lence Detection Mode Select whether to compress silence
with G.711. When there is silence, the
RTP packet is not sent.
When VAD is enabled the CPU will
stop sending packets but the IP
Phone will continue to transmit silence
packets. 0 = Disable
1 = Enable
Default = 0 X
ISSUE 1.0 SL2100
Networking Manual 9-35