background image

First Printing — February 1999

Copyright 1999

NEC Computer Systems Division

Packard Bell NEC, Inc.

1 Packard Bell Way

Sacramento, CA  95828-0903

All Rights Reserved

Proprietary Notice and Liability Disclaimer

The information disclosed in this document, including all designs and
related materials, is the valuable property of NEC Computer Systems
Division, Packard Bell NEC, Inc. (hereinafter “NEC CSD”) and/or its
licensors. NEC CSD and/or its licensors, as appropriate, reserve all patent,
copyright and other proprietary rights to this document, including all
design, manufacturing, reproduction, use, and sales rights thereto, except to
the extent said rights are expressly granted to others.

The NEC CSD product(s) discussed in this document are warranted in
accordance with the terms of the Warranty Statement accompanying each
product. However, actual performance of each such product is dependent
upon factors such as system configuration, customer data, and operator
control. Since implementation by customers of each product may vary, the
suitability of specific product configurations and applications must be
determined by the customer and is not warranted by NEC CSD.

To allow for design and specification improvements, the information in this
document is subject to change at any time, without notice. Reproduction
of this document or portions thereof without prior written approval of
NEC CSD is prohibited.

FaxFlash is a service mark and ToolTelligent is a trademark of NEC Computer Systems

Division, Packard Bell NEC, Inc.

NEC and PowerMate are registered trademarks of NEC Corporation, used under license.

All other product, brand, or trade names used in this publication are the trademarks or

registered trademarks of their respective trademark owners.

Summary of Contents for POWERMATE ES 5200 - SERVICE





















































































































































































































































































Reviews: