NEC mPD780851 Preliminary User'S Manual Download Page 233

Page: 233 / 315

233

CHAPTER 18 METER CONTROLLER/DRIVER

Preliminary User’s Manual U14581EJ3V0UM00

(2) Compare register n0 (MCMPn0)

MCMPn0 is an 8-bit register that can rewrite compare values through specification of bit 4 (TENn) of the compare

control register n (MCMPCn).

RESET input clears this register to 00H and clears hardware to 0.

MCMPn0 is a register that supports read/write only for 8-bit access instructions. MCMPn0 continuously compares

its value with the MCNT value. When the above two values match, a match signal of the sin side of meter n

is generated.

(3) Compare register n1 (MCMPn1)

MCMPn1 is an 8-bit register that can rewrite compare values through specification of bit 4 (TENn) of the compare

control register n (MCMPCn).

RESET input clears this register to 00H and clears hardware to 0.

MCMPn1 is a register that supports read/write only for 8-bit access instructions. MCMPn1 continuously compares

its value with the MCNT value. When the above two values match, a match signal of the cos side of meter n

is generated.

(4) 1-bit addition circuit

The 1-bit addition circuit repeats 1-bit addition/non-addition to PWM output alternately upon MCNT overflow

output, and enables the state of PWM output between current compare value and the next compare value.

This circuit is controlled by bits 2 and 3 (ADBn0 and ADBn1) of the MCMPCn register.

(5) Output controller

The output controller consists of a P-ch and N-ch drivers and can drive a meter in H bridge configuration by

connecting a coil.

When a meter is driven in half bridge configuration, the unused pins can be used as normal output port pins.

The relation of the duty factor of the PWM signal output from the SMnm pin is indicated by the following expression

(n = 1 to 4, m = 0, 1).

PWM (duty) =

Set value of MCMPnm

cycle of MCNT count clock

100%

255

cycle of MCNT count clock

Set value of MCMPnm

100%

255

Cautions 1. MCMPn0 and MCMPn1 cannot be read or written by a 16-bit access instruction.

2. MCMPn0 and MCMPn1 are in master-slave configuration, and MCNT is compared with

a slave register. The PWM pulse is not output until the first overflow occurs after the

counting operation has been started because the compare data is not transferred to

the slave.

Summary of Contents for mPD780851




























































































































































































































































































































Search results

Summary of Contents for mPD780851

Reviews:

Related manuals for mPD780851

Brands by name

Popular brands

NEC mPD780851, Preliminary User'S Manual

Search results

Summary of Contents for mPD780851

Reviews:

Related manuals for mPD780851

Brands by name

Popular brands