NEC mPD780851 Preliminary User'S Manual Download Page 196

Page: 196 / 315

196

CHAPTER 14 SERIAL INTERFACE SIO2

Preliminary User’s Manual U14581EJ3V0UM00

(4) Operation mode

(a) Master mode (with internal clock SCK2)

Serial interface SIO2 operates in the master mode (with internal clock SCK2) if bits 1 and 0 (SCL21 and

SCL20) of the serial operation mode register 2 (CSIM2) are set to (0, 1), (1, 0), or (1, 1).

Transfer is started when data has been read from or written to the serial I/O shift register 2 (SIO2). The

serial data is output from the SO2 pin in synchronization with the serial clock. Select the operating clock

for serial transfer by using SCL21 and SCL20.

Transfer is completed and a transmit completion interrupt (INTCSI2) occurs when all the 8 bits of the serial

data have been completely transferred.

(b) Slave mode (with external clock)

Serial interface SIO2 operates in the slave mode (with an external clock) if bits 1 and 0 (SCL21 and SCL20)

of the serial operation mode register 2 (CSIM2) are set to (0, 0). In the slave mode, the SCK2 pin operates

as an external serial clock input pin.

Serial data is transferred to SIO2 in synchronization with the externally input serial clock. After the serial

data has been received by SIO2, it is transferred to the serial receive data buffer register (SIRB2). At the

same time, the SDVA flag is set to 1 and a transmit completion interrupt (INTCSI2) occurs.

Caution

To prevent the occurrence of an overflow error, read the value of SIRB2 before the next

serial data is transferred to SIO2.

Table 14-3 below shows the status of the P03/SCK2, P04/SO2, and P05/SI2 pins in each operation mode.

Table 14-3. Operation Mode and Pin Status

Operation Mode

SIO2 Operation

Serial Operation Mode

Master/Slave

Note

P03/SCK2

P04/SO2

P05/SI2

Disabled (CSIE2 = 0)

—

Port function

Enabled (CSIE2 = 1)

Receive-only mode

Master

Serial function

Port function

Hi-Z

(MODE2 = 1)

Slave

Hi-Z

Port function

Hi-Z

Transmit/receive

Master

Serial function

Hi-Z

mode (MODE2 = 0)

Slave

Hi-Z

Serial function

Hi-Z

Note

Master/slave can be selected by setting bits 0 and 1 (CSK1 and SCL20) of the serial operation mode

Summary of Contents for mPD780851




























































































































































































































































































































Search results

Summary of Contents for mPD780851

Reviews:

Related manuals for mPD780851

Brands by name

Popular brands

NEC mPD780851, Preliminary User'S Manual

Search results

Summary of Contents for mPD780851

Reviews:

Related manuals for mPD780851

Brands by name

Popular brands