NEC mPD178053 User Manual Download Page 185

Page: 185 / 271

185

CHAPTER 13 PLL FREQUENCY SYNTHESIZER

User’s Manual U15104EJ2V0UD

13.4 Operation of PLL Frequency Synthesizer

13.4.1 Operation of each block of PLL frequency synthesizer

(1) Operation of input select block and programmable divider

The input select block and programmable divider select the input pin and division mode of the PLL frequency

synthesizer and divide the frequency in the selected division mode, according to the setting of the PLL mode

select register (PLLMD).

The programmable counter (12 bits) and pulse swallow counter (5 bits) are binary counters.

The division value (N value) is set to the programmable counter (12 bits) and swallow counter (5 bits) by the

PLL data registers (PLLRL, PLLRH, and PLLR0).

When the N value has been transferred to the programmable counter and swallow counter, frequency division

is performed in the selected division mode according to the status of bit 0 (PLLNS0) of the PLL data transfer

Figure 13-6 shows the configuration of the input select block and programmable divider.

Figure 13-6. Configuration of Input Select Block and Programmable Divider

(2) Operation of reference frequency generator

The reference frequency generator divides the 4.5 MHz output of the crystal oscillator and generates seven

types of reference frequency f

for the PLL frequency synthesizer.

Reference frequency f

is selected by the PLL reference mode register (PLLRF).

Figure 13-7 shows the configuration of the reference frequency generator.

PLL

NS0

VCOH

VHF

AMP

VHF
HF

12 bits

Internal bus

PLL data registers

(PLLRL, PLLRH, PLLR0)

5 bits

Two modulus

prescalers

(1/32, 1/33)

Programmable

counter

(12 bits)

Swallow

counter

(5 bits)

VCOL

To -DET

PLL data
transfer register

VCOHDMD

VCOLDMD

Summary of Contents for mPD178053
















































































































































































































































































Search results

Summary of Contents for mPD178053

Reviews:

Related manuals for mPD178053

Brands by name

Popular brands

NEC mPD178053, User Manual

Search results

Summary of Contents for mPD178053

Reviews:

Related manuals for mPD178053

Brands by name

Popular brands