NEC EXP803 Maintenance Manual Download Page 186

Page: 186 / 219

1. POST Error Message

Express5800/R120f-1E Maintenance Guide

186

Chapter 3 Appendix

Error Message

Cause

Solution

B006

Expansion ROM not

initialized - PCI

Slot 1D

Option ROM expansion in PCI slot
1D failed.

Disable expansion of option ROM of the
option board that is not used for OS boot.

Run SETUP, and select

Advanced

→

PCI

Configuration

→

PCI Device Controller and

Option ROM Settings

→

PCIxx Slot Option

ROM

→

Disabled

. (xx: PCI slot number)

B007

Expansion ROM not initialized
- PCI

Slot 2D

Option ROM expansion in PCI slot
2D failed.

B008

Expansion ROM not initialized
- PCI

Slot 3D

Option ROM expansion in PCI slot
3D failed.

B01A

Expansion ROM not

initialized - PCI

Slot 1A

Option ROM expansion in PCI slot
1A failed.

B022

Serial Port Configuration

Overlapped.

Overlapping serial port
configuration was detected.

Start SETUP, select

Advanced

→

Serial Port

Configuration

, and specify the setting again in

a way that the values of Base I/O or Interrupt in

Serial Port A

and

Serial Port B

will not be the

same.

B030

PCI System Error on

Bus/Device/Function

PCI SERR was detected.

Contact your sales representative.

B040

PCI Parity Error on

Bus/Device/Function

PCI PERR was detected.

B211

PCI Slot 1A - PCIe Link

Failure

Connection failure of PCIe bus was
detected on PCI slot 1A.

B212

PCI Slot 1B - PCIe Link

Failure

Connection failure of PCIe bus was
detected on PCI slot 1B.

B215

PCI Slot 1C - PCIe Link

Failure

Connection failure of PCIe bus was
detected on PCI slot 1C.

B218

PCI Slot 1D - PCIe Link

Failure

Connection failure of PCIe bus was
detected on PCI slot 1D.

B231

PCI Slot 1A - PCIE Link Width

Error

A Link Width error was detected in
PCI Slot 1A.

B232

PCI Slot 1B - PCIE Link Width

Error

A Link Width error was detected in
PCI Slot 1B.

B235

PCI Slot 1C - PCIE Link Width

Error

A Link Width error was detected in
PCI Slot 1C.

B238

PCI Slot 1D - PCIE Link Width

Error

A Link Width error was detected in
PCI Slot 1D.

B271

PCI Slot 1A - PCIe Link Speed

Error

Link Speed error was detected on
PCI Slot 1A.

B272

PCI Slot 1B - PCIe Link Speed

Error

Link Speed error was detected on
PCI Slot 1B.

B275

PCI Slot 1C - PCIe Link Speed

Error

Link Speed error was detected on
PCI Slot 1C.

B278

PCI Slot 1D - PCIe Link Speed

Error

Link Speed error was detected on
PCI Slot 1D.

B800

DXE_PCI_BUS_OUT_OF_RESOURCES

Resources to be allocated to PCI
expansion card was insufficient.

C000

The error occurred during

fan sensor reading.

An error was detected while
reading fan sensor.

C010

The error occurred during

temperature sensor reading

An error was detected while
reading temperature sensor.

C011

System Temperature out of

the range.

A temperature abnormality was
detected.

The cooling fan has failed or is clogged.
Contact your sales representative.

C020

The error occurred during

voltage sensor reading.

An error was detected while
reading voltage sensor.

Contact your sales representative.

C021

System Voltage out of the

range.

A system voltage abnormality was
detected.

C040

SROM data read error

An error was detected while
reading data on SROM.

Summary of Contents for EXP803




























































































































































































































Search results

Summary of Contents for EXP803

Reviews:

Related manuals for EXP803

Brands by name

Popular brands

NEC EXP803, Maintenance Manual

Search results

Summary of Contents for EXP803

Reviews:

Related manuals for EXP803

Brands by name

Popular brands