NEC DT920 User Manual Download

Page: 3 / 104

PREFACE

PREFACE

This manual describes operating procedures of UNIVERGE IP Phone DT930 / DT920(8LCX) Multiline
Terminal to be connected to UNIVERGE SV9300 communication server.

OUTLINE OF THIS MANUAL

This manual consists of;

INTRODUCTION

Please read through this chapter before use for your understanding and proper use of this product.

TERMINAL SETUP

This chapter describes the operations to be performed on the Menu Screen, such as speaker volume
control and LCD contrast adjustment.

FEATURE OPERATION

This chapter describes the operating procedures of service features such as make a call, answer an
incoming call, set call transfer or call hold.

APPENDIX

This chapter describes the supplemental information of this manual.

ABOUT THE MARKS USED IN THIS MANUAL

The following table shows the meaning of the marks used in this manual.

MARK

DESCRIPTION

CAUTION: The works that a user cannot perform by himself, some dangers that may cause
damages to the terminal and other cautions are described.

TIP: Useful tips when using this terminal are described.

Summary of Contents for DT920









































































































Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands

NEC DT920, User Manual

Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands