background image

DS1000 02.10.09 Release Notes

New Features in 02.10.09

18

02.10.09

DS1000 Release Notes

*. The PIN code is used for both Extension Locking and Walking Class of Service. By default, there 
are no PIN codes entered. In addition:

An extension user can dial 

ICM

 + 

##6

 to enter or change their PIN number.

The operator can dial 

ICM + ##3

 to erase a co-worker’s PIN number and unlock their extension.

To enter 1807-PIN Code data:

When you see 

PIN CODE?

, press 

HOLD

 to enter the data entry mode.

While in the data entry mode:
Vol Up scrolls right.
Vol Down scrolls left.
LND backspaces over (erases) the last entered digit.
CLEAR + HOLD erases the current entry.
CHECK restores the previous entry.
HOLD registers the entry and advances to the next prompt.
CONF exists the program.

Operation

To enable Walking Class of Service at an extension:

When using the procedures that follow to enter a PIN number or extension number:

CLEAR

 erases  your entire entry.

LND

 backspaces over (erases) the last digit entered.

1.

Press 

ICM

.

2.

Dial 

##0

At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

If your extension does not have a PIN code already entered, skip to step 4.

3.

Enter your own extension  

HOLD

.

At a 22- or 34-Button Display Telephone, you see:

Summary of Contents for DS1000











































































Reviews: