Navien NCB-24LSWE Service Manual Download

Page: 39 / 144

NCB Service Manual 37

Version 1.0

4.4.8

Viewing Basic Information

①

To enter <Basic information mode>, press [ECO] for > 2 seconds from <Normal operation mode>.

②

Press [+] or [-] to navigate through the user parameters.

③

The current parameter setting has a letter prefix followed by 3 digits.

④

Press [Reset] once to return to <Normal operation mode>.

⑤

If no changes are detected for 5 minutes, the system automatically returns to <Normal operation mode>.

Item

Description

Display

(A) Space heating water
temperature

The current outgoing space heating
water temperature is displayed.

Eg.) at 60

℃

(B) Space heating return water
temperature

The current space heating return
water temperature is displayed.

Eg.) at 60

℃

The current outgoing water
temperature is displayed.

Eg.) at 60

℃

(D) Domestic cold water inlet
temperature

The current incoming water
temperature is displayed.

Eg.) at 15

℃

Summary of Contents for NCB-24LSWE

















































































































































Search results

Summary of Contents for NCB-24LSWE

Reviews:

Related manuals for NCB-24LSWE

Brands by name

Popular brands

Navien NCB-24LSWE, Service Manual

Search results

Summary of Contents for NCB-24LSWE

Reviews:

Related manuals for NCB-24LSWE

Brands by name

Popular brands