background image

20

|

ni.com

|

Getting Started with NI SMD-7620/7621 and NI 73xx

10. Wait for installation to complete, then click 

Finish

.

11. Expand the 

Devices and Interfaces

 item under the PXI system. 

12. Right-click the remote motion controller icon and select 

Map to Local Machine

. This 

assigns a local board ID to the remote motion controller in the host system. 
Mapping the remote controller into the local system allows you to configure the controller 
through MAX exactly as you would a controller that is in the host system. You can initialize 
the controller, download firmware, and use the interactive and configuration panels exactly 
as you would on a controller installed in the host machine. You also can write VIs using the 
remote motion controller through the local board ID assigned to it.
This allows you to write and debug your VIs on the host, and then download them to the 
remote system when you are ready. All you need to change is the board ID in your VI from 
the locally assigned Board ID to the ID assigned by the remote system. 

13. Browse to 

Devices and Interfaces

 under 

My System

, where there is a shortcut icon next 

to a new controller name. 
For example, if the motion controller on the remote system is a PXI-7354, and the remote 
system has an IP address of 

123.45.678.9

, then the shortcut device would show a name 

like 

PXI-7354 (X) on 123.45.678.9 (Y)

.

X

 is the board ID assigned to the board by the remote system. Use this board ID for VIs that 

are downloaded to the remote system through LabVIEW RT. 

Y

 is the board ID assigned to the remote motion controller by the local system. Use this 

board ID for any VIs that run on the host and use the remote motion controller.

14. Close MAX.

NI UMI-7764 and NI SMD-7620/7621 Configuration and 
Installation

This section covers the hardware setup for the NI UMI-7764 and NI SMD-7620/7621 stepper 
drive. If you are using a UMI-7772/7774 refer to the 

NI UMI-7772/7774 and NI SMD-7620/7621 

Configuration and Installation

 section.

Step 1: Connect and Configure the NI UMI-7764

Complete the following steps to connect and configure your UMI-7764. 

Tip

For more information about connecting external power, encoders, and other 

motion I/O signals, refer to the 

Universal Motion Interface (UMI)-7764 User Guide 

and Specifications

.

1.

Connect the SH68-C68-S 68-pin shielded cable between the Motion I/O connector on the 
NI 73xx motion controller and the Motion I/O connector on the UMI-7764.

2.

Configure the UMI-7764 DIP switches. You must set the DIP switches to the following 
settings to match the polarity configuration for the SMD-7620/7621 stepper drive:

Inhibit Input (S2)—Active Low

Inhibit Output (S1)—Active Low

Summary of Contents for NI 73 Series


































Reviews: