background image

Getting Started with NI SMD-7620/7621 and NI 73xx

|

© National Instruments

|

17

NI Motion Controller Configuration and Installation

This section covers the hardware setup for the NI motion controller.

Caution

Before installing the NI 7330/7340/7350 motion controller refer to the 

user manual appropriate to your controller for safety and specification information. 
Failure to follow safety instructions may result in damage to equipment.

Step 1: Install NI-Motion

You must install the NI-Motion driver software 

before

 installing an NI motion controller for the 

first time. If you are upgrading from a previous version of NI-Motion, it is not necessary to 
remove the NI motion controller before installing the upgrade. The upgrade does not affect the 
existing Microsoft Windows configuration.

Note

If you are using a Real-Time OS, install LabVIEW Real-Time on the 

development computer before installing NI-Motion so that the RT support files 
install.

Complete the following steps to install the NI-Motion driver software:

Note

When installing NI-Motion, you must be logged on with administrator-level 

access. After you have restarted the system, you may need to refresh Measurement & 
Automation Explorer (MAX) to view the new controller.

1.

Insert the NI-Motion CD into the CD-ROM drive to display the NI-Motion installation 
screen, or download the latest version from 

ni.com/downloads

.

2.

If you have autorun enabled, 

autorun.exe

 runs automatically. Otherwise, double-click 

autorun.exe

3.

Follow the onscreen instructions.

Note

You must update the firmware on your NI motion controller(s) before you can 

use them with the corresponding version of NI-Motion. Refer to 

Step 2: Update 

Firmware on the Motion Controller

 in the 

Software Installation and Configuration

 

section for detailed instructions.

Step 2: Install the NI 73xx Motion Controller

The following sections explain how to install PXI and PCI motion controllers.

PXI Controllers

1.

Power off and unplug the chassis.

Caution

To protect yourself and the computer from electrical hazards, the 

computer 

must

 remain unplugged until the installation is complete.

2.

Choose an unused peripheral slot and remove the filler panel.

Summary of Contents for NI 73 Series


































Reviews: