National Instruments NI 73 Series Getting Started Download

Page: 2 / 33

ni.com

Getting Started with NI SMD-7620/7621 and NI 73xx

Step 3: Install Software on and Configure the RT PXI Controller (PXI Motion

Controllers Only)...................................................................................................19

NI UMI-7764 and NI SMD-7620/7621 Configuration and Installation...........................20

Software Installation and Configuration...................................................................................28

Step 1: Configure the Drive Using the NI Stepper Configuration Utility ........................28
Step 2: Update Firmware on the Motion Controller .........................................................29
Step 3: Configure the NI Motion Controller.....................................................................29
Step 4: Test the Motor In MAX........................................................................................31

Where to Go Next .....................................................................................................................32
Worldwide Support and Services .............................................................................................33

Connecting and Using the NI SMD-7620/7621
with the NI UMI-7772/7774

What You Need to Get Started

You need the following items to get started.

Hardware



A computer with an available PXI or PCI slot



NI 7330, NI 7340, or NI 7350 motion controller



UMI-7772/7774



SHC68-C68-S cable to connect your NI UMI and motion controller



(Optional) DB9M/DB15M/DB25M cables for UMI-7772/7774 connectivity



+24 ±10% VDC power supply (10 W minimum) for the NI UMI-7772/7774



(Optional) +5 to +30 V isolated power supply (10 to 60 W minimum, depending on I/O
requirements)

Note

The same power supply may be used for both the main +24 V power supply

and I/O. However, if you use the same power supply for both connections, there will
be no isolation between the I/O and the main power.

Summary of Contents for NI 73 Series


































Search results

Summary of Contents for NI 73 Series

Reviews:

Related manuals for NI 73 Series

Brands by name

Popular brands

National Instruments NI 73 Series, Getting Started

Search results

Summary of Contents for NI 73 Series

Reviews:

Related manuals for NI 73 Series

Brands by name

Popular brands