background image

24

|

ni.com

|

Getting Started with NI SMD-7620/7621 and NI 73xx

Step 3: Connect the Drive Ena

b

le Signal to the UMI-7764

Complete the following steps to connect the Drive Enable signal, which controls the enable
function of the drive:
1.

Connect the X3/EN- terminal (pin 6) to the Motion I/O terminal block INHOUT1 terminal.

2.

Connect the X3/EN+ terminal (pin 5) to the Motion I/O +5V terminal.

Step 4: (Optional) Connect the Drive Fault Signal to the UMI-7764

Complete the following optional steps to connect the drive fault signal to monitor the 
SMD-7620/7621 for faults.
1.

Connect the Y1+ terminal to the Motion I/O terminal block INHIN1 terminal.

2.

Connect the Y1- terminal to the Motion I/O terminal block GND terminal.

Step 5: (Optional) Connect the Encoder Signals to the UMI-7764

If your motor includes an encoder, complete the following steps to connect the encoder signals 
to the UMI-7764.
1.

Connect one end of the encoder cable to the encoder.

2.

Cut the 15-pin DSUB connector off of the other end of the cable and expose the encoder 
wires.

3.

Connect the encoder wires to the UM-7764 Motion I/O terminal block as indicated in 
Table 2.

4.

Insulate any unused wires.

Table 2.  

Encoder to UMI-7764 Motion I/O Terminal Block Connections

Encoder 

S

ignal Name

Encoder Cable 

Wire Color

Motion I/O Terminal Block 

S

ignal Name

A

blue

ENCA1

A

blue/white

ENCA1

B

yellow

ENCB1

B

yellow/white

ENCB1

I

orange

INDEX1

I

orange/white

INDEX1

GND

black

GND

+5V

red

+5 V

Summary of Contents for NI 73 Series


































Reviews: