manualshive.com logo in svg

NANOTEC ELECTRONIC N5, Technical Manual

Share
Download
NANOTEC ELECTRONIC N5 Technical Manual Download Page 47

Technical Manual N5 (CANopen)
5 General concepts

Holding torque in the Switched on state

Ex works, no holding torque is built up in the Switched on state. If a holding torque is already needed in
this state, the value "1" must be written in 3212

h

:01

h

.

Note

If  the  Holding  torque  in  the  switched  on  state  option  is  active,  changing  the  operating  mode  may
cause the motor to jerk.

Statusword

Listed in the following table are the bit masks that break down the state of the controller.

Statusword (6041

h

)

State

xxxx xxxx x0xx 0000

Not ready to switch on

xxxx xxxx x1xx 0000

Switch on disabled

xxxx xxxx x01x 0001

Ready to switch on

xxxx xxxx x01x 0011

Switched on

xxxx xxxx x01x 0111

Operation enabled

xxxx xxxx x00x 0111

Quick stop active

xxxx xxxx x0xx 1111

Fault reaction active

xxxx xxxx x0xx 1000

Fault

After switching on and successfully completing the self-test, the controller reaches the Switch on
disabled state.

Operating mode

The set operating mode (6060

h

) does not become active until the Operation enabled state. The actually

active operating mode is displayed in 6061

h

.

The operating mode can only be set or changed in the following states (see states enclosed in a
dashed border in the diagram):

•

Switch on disabled

•

Ready to switch on

•

Switched on

It is not possible to change the operating mode in running operation (Operation enabled). The Fault
state is exited if bit 7 in object 6040

h

 (controlword) is set from "0" to "1" (rising edge).

Note

If  an  unrecoverable  error  occurs,  the  controller  changes  to  the  Not  ready  to  switch  on  state  and
remains there.

5.2.2 Behavior upon exiting the Operation enabled state

Halt motion reactions

Various halt motion reactions can be programmed upon exiting the Operation enabled state.

The following graphic shows an overview of the halt motion reactions.

Version: 2.0.1 / FIR-v1650

47

Summary of Contents for N5




























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands