NANOTEC ELECTRONIC N5 Technical Manual Download Page 137

Page: 137 / 347

Technical Manual N5 (CANopen)
10 Description of the object dictionary

Error number

Description

Encoder resolution, number of pole pairs and some other values are
incorrect.

Motor current is too high, adjust the PI parameters.

Internal software error, generic

Current too high at digital output

CANopen only: Unexpected sync length

EtherCAT only: The motor was stopped because EtherCAT switched state
from OP to either SafeOP or PreOP without first stopping the motor.

Error Class[8]

This byte is identical to object 1001

Error Code[16]

Refer to the following table for the meaning of the bytes.

Error Code

Description

1000

General error

2300

Current at the controller output too large

3100

Overvoltage/undervoltage at controller input

4200

Temperature error within the controller

6010

Software reset (watchdog)

6100

Internal software error, generic

6320

Rated current must be set (203B

:01

)

7121

Motor blocked

7305

Incremental encoder or Hall sensor faulty

7600

Nonvolatile memory full or corrupt; restart the controller for cleanup work

8000

Error during fieldbus monitoring

8130

CANopen only: "Life Guard" error or "Heartbeat" error

8200

CANopen only: Slave took too long to send PDO messages.

8210

CANopen only: PDO was not processed due to a length error

8220

CANopen only: PDO length exceeded

8611

Position monitoring error: Following error too large

8612

Position monitoring error: Limit switch and tolerance zone exceeded

9000

EtherCAT: Motor running while EtherCAT changes from OP -> SafeOp,
PreOP, etc.

1005h COB-ID Sync

Function

Defines the COB-ID of the SYNC message for the SYNC protocol. The value must correspond to an
11-bit-long CAN-ID and is evaluated when the controller is restarted or on a Reset Communication
command. The generation of sync messages is not supported.

Version: 2.0.1 / FIR-v1650

137

Summary of Contents for N5




























































































































































































































































































































































Search results

Summary of Contents for N5

Reviews:

Brands by name

Popular brands

NANOTEC ELECTRONIC N5, Technical Manual

Search results

Summary of Contents for N5

Reviews:

Brands by name

Popular brands