Nabtesco RV N Series Operation Manual Download | Manualshive

Page: 46 / 62

background image

Chapter 6 Filling the Lubricant

38

Step 5

Rotate the output shaft of the reduction gear by 1 or 2 turns.



Do not use the motor to rotate the output shaft of the reduction gear for safety, if possible. If the
motor is used by necessity, run the motor at a low speed and never touch the rotation section.
Otherwise, you could be caught by the rotation section, which will result in serious injury.

Step 6

Repeat

steps 1 to 5

until the lubricant is filled up to the specified level.

Step 7

After filling the lubricant up to the specified level, wipe the lubricant off from the tapped holes for

injecting/draining grease and cap them with plugs sealed with a seal tape, etc.

Fig. 6-3

Horizontal shaft installation

Vertical shaft installation

(with shaft facing downward)

Vertical shaft installation

(with shaft facing upward)

Shaft
installation
component

Shaft installation component

Shaft installation
component

Filler

Filler

Filler

Motor mounting flange

Motor mounting flange

Motor mounting flange

Tapped hole for injecting/draining

grease (supply side)

Tapped hole for injecting/draining
grease (drain side)

Tapped hole for injecting/draining
grease (drain side)

Tapped hole for
injecting/draining
grease (drain side)

Tapped hole for injecting/

draining grease (supply side)

Tapped hole for injecting/

draining grease (supply side)

«
...
44
45
46
47
48
...
»

Summary of Contents for RV N Series































































Reviews:

No comments

Related manuals for RV N Series

Brand: Rangevision Pages: 31

Brand: JB-Lighting Pages: 60

Brand: Above All Pages: 4

Brand: J.P. SELECTA Pages: 32

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Kärcher Pages: 20

Brand: Parker Research Corp Pages: 3

Brand: Olympus Pages: 130

Brand: Martin Pages: 202

Brand: U-Line Pages: 6

Brand: Keithley Pages: 57

Brand: Parkside Pages: 37

Brand: Sagitter Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands